Atlas Welding Positioners





Atlas Model XT-100 Welding Positioners


The Atlas Model XT-100 Welding Positioner is a compact machine ideally suited for those jobs requiring rotary fixturing and positioning.  Its low profile keeps the work down to a comfortable level for the welder working at a standard height work bench.

The Model XT-100 will handle properly balanced loads of up to 100 pounds when in the horizontal position.  The heavy duty grounding circuit allows use of stick electrode, MIG or TIG welding processes.

The Model XT-100 is powered by DC permanent magnet gearhead motors.  Motor speed is controlled by a solid state variable speed controller, which is a voltage control device.  When voltage isreduced the motors turn slower.  At the low end of the motors speed ( approximately 20% of the top speed ), torque tends to fall off.  The speed ranges listed below reflect optimum torque levels.  The machines will operate at considerable slower speeds, but may not have the "lugging power" to turn loads that are near maximum weight, or are out of balance.

Some of the motor specifications may be changed ( except r.p.m.'s ) due to an upgraded motor.

Capacity: 100 lbs. properly balanced with table in horizontal position.
Table Speed:
Model XT-100 2.5 - 11 R.P.M.
Model XT-100-0-2 0.5 - 2.8 R.P.M.
Motor: DC Permanent Magnet
Power Requirement: 115V AC 60 cycle @ 1.3 Amps.  10' conductor cord with plug supplied.
Bearings: Turntable shaft supported by 2 Oilite bushings to carry radial loads and 1 ball bearing to carry thrust loads.
Motor Overload Protection: 2 Amp fuse on front panel.
Table Diameter: 9".
Table Rotation: Forward-Off-Reverse, controlled by toggle switch on front panel.
Speed Control: Solid state electronic feedback control maintains constant torque and speed from 0 - 80% of full speed.  Full speed obtained by complete clockwise rotation of front panel mounted dial.
Start / Stop Control: Rheostat-type foot switch with 10' cord.
Welding Current Grounding Circuit: 200 Amps.
Dimensions: Height 6 3/8", Width 9 1/4", Front to Back 8".
Construction: Heavy duty steel construction throughout.  Baked enamel exterior finish for easy cleaning and long lasting good looks.
Net Weight: 32 pounds.
Shipping Weight: 34 pounds.
Buy
Price
Model #
Description
$1,180.00    Model XT-100    XT-100 Positioner, 9" Table
$1,197.20    Model XT-100-0-18    XT-100 Positioner, 0-18 rpm, 9" Table
$1,208.00    Model XT-100-0-18-T10    XT-100 Positioner, 0-18 rpm, 10" Table
$1,211.00    Model XT-100-0-18-T12    XT-100 Positioner, 0-18 rpm, 12" Table
$1,187.00    Model XT-100-0-2    XT-100 Positioner, 0-2 rpm, 9" Table
$1,227.00    Model XT-100-0-2-T10    XT-100 Positioner, 0-2 rpm, 10" Table
$1,2291.00    Model XT-100-0-2-T12    XT-100 Positioner, 0-2 rpm, 12" Table
$1,258.00    Model XT-100-0-4    XT-100 Positioner, 0-4 rpm, 9" Table
$1,218.00    Model XT-100-0-4-T10    XT-100 Positioner, 0-4 rpm, 10" Table
$1,221.00    Model XT-100-0-4-T12    XT-100 Positioner, 0-4 rpm, 12" Table
$1,170.00    Model XT-100-T10    XT-100 Positioner, 10" Table
$1,173.00    Model XT-100-T12    XT-100 Positioner, 12" Table







Atlas Model XT-200 Welding Positioners


The Atlas Model XT-200 Welding Positioner is ideally suited for those short-to-long run welding jobs requiring rotary fixturing and positioning.  This compact but husky unit will help boost your production on all those hard to handle jobs requiring circular welding ( small spheres and pressure vessels, flange to pipe, pipe to pipe, etc.. )

The Model 200 will handle properly balanced loads of up to 200 pounds when in the horizontal position.  The heavy duty grounding circuit allows use of stick electrode, MIG or TIG welding processes.

The Model XT-100 is powered by DC permanent magnet gearhead motors.  Motor speed is controlled by a solid state variable speed controller, which is a voltage control device.  When voltage isreduced the motors turn slower.  At the low end of the motors speed ( approximately 20% of the top speed ), torque tends to fall off.  The speed ranges listed below reflect optimum torque levels.  The machines will operate at considerable slower speeds, but may not have the "lugging power" to turn loads that are near maximum weight, or are out of balance.

Some of the motor specifications may be changed ( except r.p.m.'s ) due to an upgraded motor.

Capacity: 200 lbs. properly balanced with table in horizontal position.
Table Speed:
Model XT-200 2.4 - 9.5 R.P.M.
Model XT-200-0-2 0.4 - 2.3 R.P.M.
Model XT-200-0-4 1.0 - 5.2 R.P.M.
Model XT-200-0-18 5.0 - 21.0 R.P.M.
Motor: DC Permanent Magnet
Power Requirement: 115V AC 60 cycle @ 1.3 Amps.  5'3" conductor cord with plug supplied.
Bearings: Turntable shaft supported by 2 Oilite bushings to carry radial loads and 2 ball bearing to carry axial loads.
Motor Overload Protection: 2 Amp fuse on front panel.
Table Diameter: 10".
Table Rotation: Forward-Off-Reverse, controlled by toggle switch on front panel.
Table Tilt: 130o forward, 15o backward, with worm and spur gear adjustment and locking device.
Speed Control: Solid state electronic feedback control maintains constant torque and speed from 0 - 80% of full speed.  Full speed obtained by complete clockwise rotation of front panel mounted dial.
Start / Stop Control: Rheostat-type foot switch with 6' cord.
Welding Current Grounding Circuit: 200 Amps.
Dimensions: Height 9 1/2", Width 10 1/2", Front to Back 12 3/4".
Construction: Heavy duty steel construction throughout.  Baked enamel exterior finish for easy cleaning and long lasting good looks.
Net Weight: 41 pounds.
Shipping Weight: 35 pounds.
Buy
Price
Model #
Description
$1,520.00    Model AT-200    XT-200 Weld Positioner, 2-10 rpm
$1,595.20    Model AT-200-0-18    XT-200 Positioner, 0-18 rpm, 10" Table
$1,575.00    Model AT-200-0-18-T12    XT-200 Positioner, 0-18 rpm, 12" Table
$1,570.00    Model AT-200-0-2    XT-200 Positioner, 0-2 rpm, 10" Table
$1,605.00    Model AT-200-0-2-230    XT-200 Positioner, 0-2 rpm, 10" Table, 230V
$1,565.00    Model AT-200-0-2-T12    XT-200 Positioner, 0-2 rpm, 12" Table
$1,575.00    Model AT-200-0-4    XT-200 Positioner, 1-5.2 rpm, 10" Table
$1,590.00    Model AT-200-0-4-T12    XT-200 Positioner, 1-5.2 rpm, 12" Table
$1,600.00    Model AT-200-230V    XT-200 Positioner, with 230V Option
$1,805.00    Model AT-200-3JC    XT-200 Positioner with 3 Jaw Chuck, 2.4 - 9.5 rpms
$405.00    Model AT-3JC    3 Jaw Chuck, 5"
$1,625.00    Model AT-200-AP    XT-200 Positioner, Argon Purge, 10" Table
$1,725.00    Model AT-200-AP-0-18    XT-200 Positioner, Argon Purge, 0-18 rpm
$1,745.00    Model AT-200-AP-0-18-T12    XT-200 Positioner, Argon Purge, 0-18 rpm with 12" Table
$1,665.00    Model AT-200AP-0-2    XT-200 Positioner, Argon Purge, 0-2 rpm, 10" Table
$1,680.00    Model AT-200AP-0-2-T12    XT-200 Positioner, Argon Purge, 0-2 rpm, 12" Table
$1,690.00    Model AT-200AP-0-4    XT-200 Positioner, Argon Purge, 0-4 rpm, 10" Table
$1,715.00    Model AT-200AP-0-4-T12    XT-200 Positioner, Argon Purge, 0-4 rpm, 12" Table
$1,650.00    Model AT-200-T12    XT-200 Positioner, Argon Purge, 12" Table
$1,715.00    Model AT-200-HDG    XT-200 Positioner with Heavy Duty 350+ Amp Ground
$1,510.00    Model AT-200-T12    XT-200 Positioner, 12" Table







Atlas Model 500 Welding Positioners


The Atlas Model 500 Welding Positioner is designed for those heavy parts turning jobs that require a truly rugged industrial piece of equipment.  It will handle properly balanced loads of 500 pounds in the horizontal position.

Four brass grounding brushes in constant contact with the table mounting boss route welding current to a 1/2"-13 grounding stud at the rear of the machine.  Heat generating welding current does not pass through the bearings or shaft, which greatly enhances bearing and shaft life.

Convenient front panel mounted controls are protected from damage by the overhang of the 14" table and also by the heavy-duty handles that aid in moving the machine.

Table operating speed is set by adjusting the speed control dial. A forward-off-reverse switch controls table rotation direction.  A full speed override switch is provided which allows the operator to rapidly advance the table to a new position to accommodate intermittent or stitch welding techniques. Releasing the switch returns the table rotation to the previously selected operating speed.

The brake-on-off switch allows the operator to select Dynamic Brakingt hat rapidly stops the table rotation when the foot switch is released. Off position on this control allows the table to coast to a smooth stop when braking is not required. Dynamic braking may induce additional heat into the motor and may not be needed for all jobs. This Model 500 selective control feature lets you choose.

The Model 500's foot switch controls the on-off function of the table. It's ergonomic, low profile design lets the operator rest his heel comfortably on the floor for strain free, day long use. A safety enclosure guards the switch. Front panel mounted fuse holder provides motor overload protection. All circuit boards, switches, wiring, and cord sets are mounted to the front panel. In the event of electrical problems the panel can be quickly removed for diagnostics and repair. On request and for additional charge, all control panel functions can be supplied in a remote control box connected to Model 500 via a cord set.

Capacity: 500 lbs. properly balanced with table in horizontal position.
Table Speed: 0 - 3.0 R.P.M.
Table Diameter: 14" x 5/8" thick.  Percision laser cut slots are 13/32" wide
Motor: 1/4 HP DC
Welding Ground Circuit: 400 Amps.
Control Panel Functions:
Table Rotation
Speed Control
Full Speed Override
Dynamic Braking
 
Forward-Off-Reverse
Full range precision control with IR compensation.
On-Off
On-Off
Start - Stop Control: Foot switch with 8 foot cord.
Overload Protection: Panel mounted fuse.
Power Requirements: 115 V AC 50/60 Hz. 10' cord with plug.
Dimension: Height: 10", Width: 14-1/2", Front-to-Back: 15-1/2".
Weight: 95 pounds.
Buy
Price
Model #
Description
$4,200.00    Model AT-500    500 lb capacity welding positioner.
$4,030.00  Model AT-500 AP  500 lb capacity welding positioner with Argon purge.
$350.00    5" 3 Jaw Chuck    5" 3 Jaw Chuck.





Atlas Model 1200 Pipe Mate Welding Positioners


The Atlas dual speed Model 1200 Pipemate easily rotates pipe and tube sizes from 1 ½” to 17” diameter weighing up to 1,200 pounds (with one end of the pipe supported on an appropriate free turning roller, such as our optional Idler Rolls).

Two 6" x 2" hard rubber tired wheels, (durometer rating of 70-80, Shore A) are driven at identical speed and are heat and abrasion resistant.  Power is provided by a DC permanent magnet motor and hardened secondary gearing.  Pipemate features dual speed ranges; 0-35 IPM or 0-70 IPM.  Speed range is changed by removing the side cover and reversing the position of the secondary gears.  The speed control dial is located on the front panel, along with a forward-off-reverse switch and easily accessible 2 amp fuse for overload protection.  A broad spectrum, high frequency filter prevents erratic motor operation when TIG welding.  The on-ff foot switch initiates rotation and is protected by a steel safety enclosure.

An optional, non-powered, Atlas IDLER ROLL is an ideal mate for supporting the other end of work pieces.  Wheel size, wheel stance and tires are identical to those on the PIPEMATE.

A specially designed, heavy duty work stand for the PIPEMATE and IDLER ROLL is also available for welding convenience.

Capacity: 1,200 lbs. balanced loads with Idler Roll.  1,200 lbs. balanced loads with Idler Roll ( Model 1200 ).
Diameter Range: 1 1/2" to 17" diameters
Dual Speed: 0 - 35 ipm or 0 - 70 ipm ( Model 1200 )
Drive Motor: DC Permanent Magnet
Power Requirements: 115V, 50/60 Hz.
Bearings: Heavy duty axle roller bearings.
Motor Overload Protection: 1.5 amp fuse.
Rotation: Reversible.
Speed Control: Solid state fully variable over entire speed range.
Start / Stop Control: Footswitch ( on / off ) with 8' cable.
Construction: Heavy duty steel construction.  Durable enamel finish.  Two handles for easy handling.
Shipping Weight: 56 pounds.


Buy
Price
Model #
$1,555.00    1200 capacity dual SP
$1,638.00    1200 capacity dual SP with 230V
$  260.00    Idler Roll
$  240.00    Idler Roll Stand


Shipping to be determined

Last update 15 December 2021

All products subject to availability.
Prices are subject to change.